备注:
对于每一个路由器来说,都有一个控制台接口(Console),管理员可以通过RS-232 线缆把控制口和一个终端的主口连接起来,通过这个终端对路由器进行配置.
终端通讯参数设置为:
| 速度: | 9600bps | |||
| 起始位: | 1位 | |||
| 数据位: | 8位 | |||
| 停止位: | 1或2位 | |||
| 校验: | 无 |
待终端通讯参数设置完毕后,接好路由器控制台,请先打开终端电源,后开路由器电源,之后就进入初始配置了.屏幕出现(以Cisco 2501为例):
System
Bootstrap, Version 5.2(5), RELEASE SOFTWARE
Copyright (c) 1986-1994 by cisco Systems
2500 processor with 2048 Kbytes of main memory
大约停顿1-2分钟,系统调入boot,请耐心等待
F3: 3996764+54172+225404 at 0x3000060
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-I-L), Version 11.2(1), MAJOR RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 30-Sep-96 12:07 by ajchopra
Image text-base: 0x030215A4, data-base: 0x00001000
cisco 2500 (68030) processor (revision D) with 2048K/2048K bytes of memory.
Processor board ID 02327592, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read ONLY)
Notice: NVRAM invalid, possibly due to write erase.
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes]: Return
你是否要进入初始化配置?默认"是".
First, would
you like to see the current interface summary? [yes]: Return
首先,你是否想看一下当前端口的状态?默认"是".
Any interface
listed with OK? value "NO" does not have a valid configuration
下面会列出当前路由器所具有的硬件配置(包括局域网口和广域网口,以及个端口当前状态等等.)
| Interface | IP-Address | OK? | Method | Status | Protocol | ||||||||
| Ethernet0 | unassigned | NO | unset | up | down | ||||||||
| Serial0 | unassigned | NO | unset | down | down | ||||||||
| Serial1 | unassigned | NO | unset | down | down |
Configuring
global parameters:
Enter host name [Router]: JSRouter
设置系统名,如JSRouter.
The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.
Enter enable secret: cisco
设置进入priviledged EXEC 的密码
The enable password is used when there is no enable secret
and when using older software and some boot images.
Enter enable password: cisco1 (1)
Enter virtual terminal password: cisco
设置进入虚拟终端登录到路由器的口令,即远程登录(telnet)的口令
Configure SNMP Network Management? [yes]: Return
是否设置简单网管协议?
Community string [public]: Return
Configure IP? [yes]: Return
是否设置IP协议?
Configure IGRP routing? [yes]: Return (2)
是否设置IGRP 路由协议?
Your IGRP autonomous system number [1]: Return
(3)
你的IGRP 路由协议自治系统号(AS),默认为1.
Configuring interface parameters:
下面配置端口参数
Configuring interface Ethernet0: Return
Is this interface in use? [yes]: Return
Configure IP on this interface? [yes]: Return
IP address for this interface: 1.1.1.1
Number of bits in subnet field [0]: Return (4)
Class A network is 1.0.0.0, 0 subnet bits; mask is /8
以上是配置以太口0,假设IP地址是1.1.1.1,掩码是255.0.0.0.
Configuring interface Serial0: Return
Is this interface in use? [yes]: Return
Configure IP on this interface? [yes]: Return
Configure IP unnumbered on this interface? [no]: Return
IP address for this interface: 2.1.1.1
Number of bits in subnet field [0]: Return
Class A network is 2.0.0.0, 0 subnet bits; mask is /8
以上是配置串口0,假设IP地址是2.1.1.1,掩码是255.0.0.0.
Configuring interface Serial1: Return
Is this interface in use? [yes]: no
以上是当不需要用串口1时,请敲入no.
The following configuration command script was created:
hostname JSRouter
enable secret 5 $1$Bv.r$j/Zm2B6jw9UTQPxLGZjAz.
enable password cisco1
line vty 0 4
password cisco
snmp-server community public
!
ip routing
!
interface Ethernet0
ip address 1.1.1.1 255.0.0.0
!
interface Serial0
ip address 2.1.1.1 255.0.0.0
!
interface Serial1
shutdown
no ip address
!
router igrp 1
network 1.0.0.0
network 2.0.0.0
!
end
Use this configuration? [yes/no]: yes (5)
确认当前配置后,把当前配置写入NVRAM 中.这样以后开机自动把配置调入内存,不需要重新配置了.
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINK-3-UPDOWN: Interface Serial1, changed state to down
%LINK-5-CHANGED: Interface Serial1, changed state to administratively down
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-I-L), Version 11.2(1), MAJOR RELEASE SOFTWARE (fc1
)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 30-Sep-96 12:07 by ajchopra
JSRouter> en
Password: (敲入密码, 不反显的)
JSRouter#
